Skip to main content

Filter By:

  • Show More Brands

  • Show Fewer Brands
  • Show More Sizes
  • Show Fewer Sizes
  • Show More Model Years
  • Show Fewer Model Years

Wheels

$8.10
Front axle conversion kits convert your hub to fit a new axle measurement or for a new group set.
$8.95
Lightweight and easy to install, there are Ritchey rim strips for all wheel sizes and types. - Easily snaps over your rims - Stretchy, tightly woven material provides a close fit and protects from abrasion - Sold as a pair - Not for tubeless set up
$8.99
This lightweight, high-pressure rim tape offers great protection against spoke hole flats and is easy to install. This Italian-made tape is light and thin, so it will not inhibit tire fitting. Nylon elastic material is used to ensure a snug fit without movement.
$8.99
You need rim tape to keep your tubes from blowing through the spoke holes, especially when landing big airs. WeThePeople's got your back, though. If your's is questionable, you better replace it with this WTP Nylon Rim Tape, a perfect fit with Logic Rims. - Strong - Lightweight - Tube-proof
$8.99
Whisky’s tubeless rim tape is designed to make setup as easy as possible. Elasticity allows for smooth, even adherence while translucency lets you see where the tape contacts the rim. Different widths available to fit almost any rim.
$9.00
This outer receiver unit works with the CJ-S700 Cassette Joint Unit for Shimano Alfine SG-S700 internally geared hub. This part can become worn, cracked, or torn, exposing the shift cable and possibly other components to unwanted dirt, water, mud, you name it. You don't want that.
$9.95
Small component with a large impact. A poorly constructed or unsuitable tyre rim tape can be the cause of many punctures. It is especially important with hollow section rims to use a pressure-resistant rim band which covers the entire rim. The fabric-reinforced Continental Easy Tape rim protector is designed for use under high air pressure conditions. The various widths enable a perfect fit for all standard rims. The high pressure design for racing cyclists withstands up to 220 psi, without becoming deformed. The flat construction type also significantly eases the job of tyre fitting.
$9.95
The Wolf Tooth Rear Axle uses a captive steel washer under the head to reduce friction on the dropout face. This protects your expensive frame, transfers more of the tightening torque to clamping load for a stiffer interface and prevents the axle from sticking or galling when you want to remove it. - Made in Minnesota to aerospace standards
$9.99 - $22.99
- Press fit designed to work the hub's non-drive side collar.
$9.99
Replaceable hub guard for the Odyssey Vandero Pro and GSport Roloway front hubs. Made from a special proprietary plastic blend for increased durability. Sold individually. Features: - Proprietary Plastic - Press Fit
$9.99 - $13.49
WTP's Helix hub guards are designed to work on The Helixline of hubs, replacing the cones for a perfect fit without having to spread your dropouts. - Includes heat-treated chromoly adaptor to replace hub cone nuts for a perfect fit - Rear Hub guards are compatible with Helix V1 and Helix V2 freecoaster hubs and many other "KHE" style freecoasters on the market
$10.00
Using Easton End Caps allows you to utilize the versatility of Easton Wheels. Easton wheels are interchangeable with a variety of wheel mounting standards.
$10.00
Pawl and spring kits for Easton hubs.
$10.00
- Replacement part for Surly hubs
$10.80 - $15.00
- Replacement straight pull spokes for Zipp 88 (Front) and 188 (Rear) Hubs
$10.95
- High performance adhesive tape, a great pairing with Velox Cement - Each roll is usually adequate for gluing two tubular tires - Protects tube from spoke/nipple/rim puncture
$11.50 - $48.00
We designed Teravail tubeless tape for no-hassle installation. Its slight stretch allows the tape to easily conform to your rims. The translucent material shows you exactly where the tape makes contact. It's tacky enough to prevent shifting but easy to pull up if needed, and it won't leave residue on your rims. - Teravail Tubeless Tape comes in a variety of widths to fit almost any rim. - Teravail Tubeless Tape is available in a variety of widths and roll lengths. - Ten-meter length is enough for a single layer on approximately four wheels
$11.95
Pawl and spring service kit for all Ritchey wheels and hubs V4 and up.
$11.99 - $15.99
The Muc-Off Tubeless Rim tape is made from their proprietary performance material with a pressure-sensitive adhesive to provide just the right amount stretch whilst maintaining durability and strength needed to create a lasting airtight seal. Semi-transparent material makes locating the valve hole easy.
$12.50
Replacement bearings for Stan's NoTubes Neo hubs. Includes 2 bearings. - 26mm OD x 15mm ID - 7mm thick
$12.75
- Strong nylon reinforced material handles high-pressures - Adhesive backed for a secure fit - Does not rot - 0.5mm thick
$12.95
Authentic service bearing kit for Ritchey mountain bike and road wheels. - Bearing service kit for Phantom Flange rear hubs Includes #6903 (x1pc) & #699 (x1pc)
$13.00
The same spoke thread treatment used by Stan's pro wheel builders is now available to everyone. Stan's SRD Spoke Powder fills the threads of the spoke and functions as both a lubricant during assembly and a thread lock once built. Each bottle contains 24g (.8oz) which will treat approximately 300 wheels. The PTFE powder in Stan's SRD Spoke Powder acts as a barrier, keeping the metal of the nipple from bonding to the metal of the spoke and preventing spoke wind up during build or adjustment. In promoting a smoother turning nipple, the powder also ensures more accurate and consistent wheel builds, with less “ping and pop" during and after the build. The powder also fills the threads of the spoke to act as a thread lock that prevents loosening and de-tensioning and is particularly well suited for mechanically locking nipples such as Sapim's Secure Lock. - Improves tension consistency and overall build quality - Prevents spoke wind up - Offers secure thread lock between spoke and nipple - Prevents corrosion between spoke and nipple - Can be used dry or as a slurry - Works great with mechanically locking nipples
$13.73
Wheels Manufacturing cones are precision machined to Shimano Ultegra or higher quality standards. This ensures that our cones fit correctly, run smoothly and have a long service life. - Compatible with Shimano Rear 10mm x 1 axle - Shimano Rear Cone - Cone Wrench Size: 15mm - Threads: 10mm x 1 - Diameter: 16.9mm - Length: 15mm - 1 cone per bag Note: O-ring / seal not included. Check the seal groove closely. This cone has a narrower groove than cone CN-R002. COMPATIBLE HUBS: - 105 FH-5700, 9 speed (right side cone) - 105 SC 1051, 7 Speed Rear - RX100 A551, 8 Speed Rear - RSX 410, 7 Speed Rear - Deore LX M550, 7 Speed Rear - Deore Mtn LX M550, 7 Speed Rear
$13.73
Wheels Manufacturing cones are precision machined to Shimano Ultegra or higher quality standards. This ensures that our cones fit correctly, run smoothly and have a long service life. - Fits: Joytech, Joy U, KK 10mm x 1, rear - Compatible with 10mm x 1 axle - Cone Wrench Size: 15mm - Threads: 10mm x 1 - Diameter: 17.0mm - Length: 13.8mm - 1 cone per bag COMPATIBLE HUBS: - Joytech, Joy U, KK 10mm x 1, rear - Taiwanese rear hubs with 10mm x 1 axle
$13.73
Wheels Manufacturing cones are precision machined to Shimano Ultegra or higher quality standards. This ensures that our cones fit correctly, run smoothly and have a long service life. - Compatible with Shimano Rear 10mm x 1 axle - Shimano Rear Right Cone - Threads: 10mm x 1 - Diameter: 16.9mm - Length: 12.5mm - Cone Wrench Size: 15mm - 1 cone per bag COMPATIBLE HUBS: - Sora FH-3300, 9-spd Rear
$13.90
- Green colored spoke prep remains pliable for adjustments - Helps keep spoke nipples from loosening
$13.95
- 10mm axle holes for mountain bike applications - 14mm axle holes for BMX applications - Heavy duty steel protects frame, tensions chain - M8 threading, Nylock nut
$13.95
- 14 gauge forged 7075 alloy with CNC finish - Matches Halo and Gusset anodized colors perfectly - Sold in bags of 50 - length: 12mm
$13.95
- Precision CNC machined 6061 aluminum axle nuts - Compare stock steel nuts at 44 grams versus alloy nuts at 16 grams